Water management

Water Management

Considering the current downturn in crude prices, there is a renewed interest in recycling produced water for reuse in hydraulic fracturing in the development of unconventional resource plays.

Considering the current downturn in crude prices, there is a renewed interest in recycling produced water for reuse in hydraulic fracturing in the development of unconventional resource plays. As the hydrocarbons are produced, large quantities of water containing high amounts of total dissolved solids (TDS) are also produced in the process. Most of the produced water usually is reinjected into disposal wells. This practice has become a topic of public concern after reports of earthquakes began approximately 5 years ago in the central United States, where disposal wells are heavily used. Reusing produced water as the base fluid for hydraulic fracturing not only alleviates the operators’ dependence on fresh water but also lowers the overall cost of fracturing treatments.

Produced water usually is composed of natural formation water and flowback water. Flowback water is water that was a large component of fracturing fluids injected into a well at high pressure as a part of the hydraulic-fracturing treatment. Within a few hours to a few weeks after the fracturing job is completed, a portion of the injected water returns to the surface. It typically contains much higher levels of chemical constituents, including TDS, than the original fracturing fluid did.

The amount of produced water, and the chemical constituents (i.e., anions and cations) and their concentrations present in the produced water, usually varies significantly over the lifetime of a field. Early in the process, the water-generation rate can be a small fraction of the oil-production rate, but it can increase with time to tens of times the rate of oil produced. Compositionally, the changes are complex and field-specific because they are a function of formation mineralogy, oil and water (both in-situ and injected) chemistry, rock/fluid interactions, type of production, and the required additives for oil-production-related activities.

To reuse the high-TDS produced water as a base fluid for formulating crosslinked-gel-based fracturing fluids, the water must first be treated to remove ions that hinder the development of crosslinked fluid or that cause scale buildup in the wellbore. An ideal solution would be to reuse the high-TDS produced water in subsequent fracturing treatment with no treatment or fit-for-purpose treatment.

The papers featured this month deal with a fit-for-purpose treatment of produced water, a new guar-based system that allows the use of 100% produced water without treatment as a base fluid, and produced-water reinjection. I hope you enjoy reading the selected papers and search for additional papers in the OnePetro online library.

This Month's Technical Papers

Fit-for-Purpose Treatment of Produced Water for Hydraulic Fracturing in the Permian Basin

Solving Produced-Water Challenges With a Novel Guar-Based System

Produced-Water Reinjection—Case Study From Onshore Abu Dhabi

Recommended Additional Reading

SPE 175206 Produced-Water Injection—The Challenges Faced by N. Bhola, Jorin, et al.

SPE 177067 The Integrated Approach to Formation-Water Management Part 2: Field Applications and Best Practices by R. Correa, AGIP Oil Ecuador, et al.

SPE 181588 Reuse of Produced Water by Membranes for Enhanced Oil Recovery by Remya Ravindran Nair, University of Stavanger, et al.

Syed A. Ali, SPE, is a consultant. Previously, he was a technical adviser with Schlumberger, and, before that, he was a Chevron Fellow with Chevron Energy Technology Company. Ali became an SPE Honorary Member in 2015, and he received the 2014 SPE DeGolyer Distinguished Service Medal, the 2012 SPE Distinguished Service Award, and the 2006 SPE Production and Operations Award. He served as an SPE Distinguished Lecturer in 2004–2005. Ali holds BS, MS, and PhD degrees. He served as executive editor of SPE Production & Operations and currently serves on several SPE committees, including the JPT Editorial Committee, the Completion Optimization and Technology Award Committee, the Well Operations Subcommittee, and the Completions Advisory Committee. Ali can be reached at syed1940@gmail.com.